Model No. RBBE2057.0Serial No. Write the serial number in thespace above for future reference.QUESTIONS?As a manufacturer, we are com-mitted to provid
1011. See the left inset drawing. Identify the TopTube (16), the Bottom Tube (17), and theAnkle Brace Tube (18); the Tubes have differ-ent lengths and
1114. Identify the two Rear Ankle Braces (34), whichhave holes in the indicated locations. Slide a Rear Ankle Brace (34) onto the AnkleBrace Tube (18)
1216. Pull the Short Adjustment Knob (74) out as faras it will go, and insert the end of the LegFrame (10) a few inches into the BackrestFrame (8).See
1318. Attach a Handle (12) to the Left Frame (4) withtwo M10 x 80mm Button Bolts (52), two M10Curved Washers (50), and two M10 NylonLocknuts (65). Att
14This section explains how to adjust the inversion table. See DEVELOPING A PROGRAM on page 17 for impor-tant information about how to get the most be
151133191034SETTING THE INVERSION ANGLEThe inversion table can be set to rotate between15° and 90°, in 15° increments. To set the inver-sion angle, pu
16This section explains how to rotate back on the inversion table, and then return to the starting position. Beforeusing the inversion table, see the
17BENEFITING FROM USING THE INVERSION TABLEIf you feel nauseated while using the inversion table,return to the starting position. Note that it may tak
18Key No. Qty. Description Key No. Qty. Description1 1 Left Base2 1 Right Base3 1 Center Base4 1 Left Frame5 1 Right Frame6 1 Center Frame Extension7
EXPLODED DRAWING—Model No. RBBE2057.0 R1207A1234567891011121213141516171819202134342222232425262728293031323270323369393840404141424242743744444645454
2WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2I
LIMITED WARRANTYPart No. 263046R1207A Printed in China © 2007 ICON IP, Inc.ORDERING REPLACEMENT PARTSICON Health & Fitness, Inc. (ICON) warrants t
3WARNING: To reduce the risk of serious injury, read all important precautions andinstructions in this manual and all warnings on the inversion table
4HandleLeft FrameLong Adjustment KnobBackrestHeadrestFoot PlateAnkle BraceAnkle Lock AssemblyIndex HandleShort Adjustment KnobRight FrameASSEMBLED DIM
5M10 NylonLocknut (65)M8 NylonLocknut (72)M6 Washer (62)M4 x 15mmScrew (58)M10 x 85mm Button Bolt (51)M10 x 95mm Button Bolt (73)M6 x 18mmButton Screw
61.Press a 63mm Round Cap (40) onto the LeftBase (1). Attach a Foot (42) to the Left Base (1) with anM4 x 20mm Screw (71). Next, tighten aLeveling Foo
72. Attach the Left Base (1) to the Right Base (2)with two M10 x 80mm Button Bolts (52), fourM10 Curved Washers (50), and two M10Nylon Locknuts (65).
85. Attach the Center Base (3) to the Left andRight Bases (1, 2) with four M10 x 80mmButton Bolts (52), four M10 Curved Washers(50), and four M10 Nylo
98. Attach the Top Cover (23) and the BottomCover (24) to the Center Frame (7) with twoM4 x 15mm Screws (58) and an M4 x 30mmScrew (63).Attach the Cen
Comments to this Manuals